Huis > Nieuws > Dagelijks Nieuws > Sandblasting operation processing
Nieuws
Dagelijks Nieuws
Industry News
Bedrijfsnieuws
Certificeringen

Geschenken van de liefde in het oude China

Jade hangers De oude Chinezen gaven meestal hun geliefden iets kleins, zodat ze gemakkelijk overal kan nemen. Een jade hanger is een goede keuze. Bove...

wat is zacht staal

Milde staalsoort is een soort koolstofstaal met een lage hoeveelheid koolstof - het is eigenlijk ook bekend als "staal met laag koolstofgehalte." Hoew...

10 verschillen tussen een zakenman en een ondernemer

10 verschillen tussen een zakenman en een ondernemer Zakenmensen en ondernemers hebben veel overeenkomsten. Maar ze zijn niet hetzelfde soort mensen. ...

Wat is ALOCROM 1200 oppervlaktebehandeling

Wat is ALOCROM 1200oppervlakte behandeling Alocrom 1200 is een snelniet-elektrolytisch dompelproces dat een uitstekende bescherming tegen corrosie bie...

Wat is Kydex-materiaal

Wat is Kydexmateriaal Kydex is een lijn van thermoplastacryl-polyvinylchloride materialen vervaardigd door Sekisui SPI. Het heeft een breedverschillen...

Wat is Overmolding?

Overmouleren wordt ook 2 maal spuitgieten genoemd in China. In vergelijking met de materiaalbinding door derden, maakt het overgietproces het proces s...

Wat is Alodine 5200 oppervlaktebehandeling

Wat is Alodine 5200oppervlakte behandeling Alodine 5200-behandeling is een chroomvrij product en specifiek geformuleerd voor de behandeling van alumin...

Wat is Black Oxide?

Black Oxide, zwart worden, oxideren, oxiding, zwart passiveren, gun bluing. . . deze termen verwijzen allemaal naar het proces van het vormen van een ...

Hoe en wanneer je bochtreliëfs moet toevoegen aan plaatmetalen onderdelen

Wat is een Bend Relief? Een Bend Relief is niets meer dan twee kleine incisies gesneden in een stuk plaatwerk om het metaal tussen de twee te bevrijde...

Privacybeleid

We verzamelen en bewaren uw informatie in een formulier niet.
Neem contact op
Vice General Manager: Ivy
Tel: 86-13312953695
Tel: 86-755-82737317 / 82737469
Fax: 86-755-82737710
E-mail: verkoop. china@xy-global.com
Postcode: 518129
Uit Toevoegen: Room1702,17F, Building # 4, Tianan Cloud Park, No.2018 Xuegang Rd., Longgang District, Shenzhen.
Factory Add: Daling Industrial Area, Shaling, Fenggang Town, Dongguan City Contact nu

Sandblasting operation processing

Sandblasting operation processing

naky www.diecastingpartsupplier.com 2014-12-05 17:23:39
Sandblasting operation processing

1, the first open lights, after opening the compressed air valves, air spray nozzle 2 to 5 minutes , so that the pipe in the water spray out , so as not to wet sand and then shutting the valve will lose sand compressed air tube into the sand .

2 , and then into the working parts inside ( small pieces can be fitted with a basket ) , shut the door .

3, then start ventilation equipment , air valve open , blasting . When sandblasting nozzle should be tilted 30 ° ~ 40 °; should be evenly rotated or flipped back and forth slowly moving parts and parts or nozzles , so that parts of the surface subjected to a uniform jet , silver gray until the whole surface of the part so far. ( For the basket to hold small parts, parts jitter flip straight to reach blasting requirements . )

4 , where the parts have precision or finish requirements , you can not blast . If there are local requirements should not blast site on the same part , can only after blasting should be protected.

5 , each batch of parts after spraying , immediately shutting compressed air valve , and then unpack parts.

6, after the general parts sand , handed down procedure, as anti-rust treatment . But matt chrome parts , sandblasting plating treatment immediately after passing .

7 , only requires a cast iron hair spray blasting , sandblasting rust treatment is not performed immediately after passing the post processing plant
.