منزل، بيت > أخبار > الأخبار اليومية > Die Casting - Draft
أخبار
الأخبار اليومية
صناعة الأخبار
أخبار الشركة
الشهادات

هدايا الحب في الصين القديمة

اليشم المعلقات الصينية القديمة عادة ما أعطى عشاق شيء صغير بحيث يمكن أن تأخذ بسهولة...

ما هو الفولاذ الطري

الفولاذ الطري هو نوع من الفولاذ الكربوني مع كمية منخفضة من الكربون - وهو معروف في ا...

10 الاختلافات بين رجل أعمال ورجل أعمال

10 الاختلافات بين رجل أعمال ورجل أعمال رجال الأعمال ورجال الأعمال لديهم العديد من أ...

ما هو ألوكروم 1200 المعالجة السطحية

ما هو ألوكروم 1200المعالجة السطحية ألوكروم 1200 هو سريعغير-- كهربائيا تراجع العملية ال...

ما هي المواد كيدكس

ما هو كيدكسمواد كيدكس هو خط من بالحرارةالاكريليك والبولي فينيل كلوريد المصنعة من ...

ما هو Overmolding؟

يسمى أيضا overmolding 2 حقن صب مرة في الصين. مقارنة مع الترابط المادي لجهة خارجية ، فإن عم...

ما هو ألودين 5200 المعالجة السطحية

ما هو ألودين 5200المعالجة السطحية العلاج ألودين 5200 هو الكروممنتج مجاني وصاغ خصيصا ل...

ما هو اكسيد الاسود؟

أوكسيد أسود ، اسوداد ، أكسدة ، أكسدة ، تخميل أسود ، مسدس غليظ. . . تشير جميع هذه المصط...

كيف ومتى تضيف نقوش ثني إلى أجزاء معدنية ورقة

ما هو الانحناء؟ إن الإغاثة المنحنى ليست أكثر من شقتين صغيرتين مقطوعة في قطعة من ال...

سياسة خاصة

لن نقوم بجمع وتخزين معلوماتك بأي شكل من الأشكال.
اتصل بنا
نائب المدير العام: Ivy
هاتف: 86-13312953695
هاتف: 86-755-82737317/82737469
الفاكس: 86-755-82737710
البريد الإلكتروني: المبيعات. china@xy-global.com
الرمز البريدي: 518129
Off Add: Room1702،17F، Building # 4، Tianan Cloud Park، No.2018 Xuegang Rd.، Longgang District، Shenzhen.
إضافة المصنع: Daling Industrial Area، Shaling، Fenggang Town، Dongguan City اتصل الآن

Die Casting - Draft

Die Casting - Draft

NADCA Design 2020-05-26 23:38:06

Draft is the amount of taper or slope given to cores or other parts of the die cavity to permit easy ejection of the casting from the die casting die.

All die cast surfaces which are parallel with the opening direction of the die require draft (taper) for proper ejection of the casting from the die. This draft requirement, expressed as an angle, is not constant. It will vary with the type of wall or surface specified, the depth of the surface and the alloy selected.

The amount of draft required for holes, inside and out walls is different. Untapped holes require the most draft because the casting shrinks (while cooling) with great force around the die steel while forming the inside surface of the hole. Inside walls also are subjected to the casting shrinking onto the die steel that creates the surfaces of inside walls. Outside walls require the least amount of draft because the casting shrinks away from the die steel forming outside surfaces.

When proper draft is applied to a die casting it is much easier to open the die and also eject the casting from the die surfaces. A die that is easy to open and eject castings from will result in a more precise die casting with a higher surface quality.