منزل، بيت > أخبار > الأخبار اليومية > Sandblasting operation processing
أخبار
الأخبار اليومية
صناعة الأخبار
أخبار الشركة
الشهادات

هدايا الحب في الصين القديمة

اليشم المعلقات الصينية القديمة عادة ما أعطى عشاق شيء صغير بحيث يمكن أن تأخذ بسهولة...

ما هو الفولاذ الطري

الفولاذ الطري هو نوع من الفولاذ الكربوني مع كمية منخفضة من الكربون - وهو معروف في ا...

10 الاختلافات بين رجل أعمال ورجل أعمال

10 الاختلافات بين رجل أعمال ورجل أعمال رجال الأعمال ورجال الأعمال لديهم العديد من أ...

ما هو ألوكروم 1200 المعالجة السطحية

ما هو ألوكروم 1200المعالجة السطحية ألوكروم 1200 هو سريعغير-- كهربائيا تراجع العملية ال...

ما هي المواد كيدكس

ما هو كيدكسمواد كيدكس هو خط من بالحرارةالاكريليك والبولي فينيل كلوريد المصنعة من ...

ما هو Overmolding؟

يسمى أيضا overmolding 2 حقن صب مرة في الصين. مقارنة مع الترابط المادي لجهة خارجية ، فإن عم...

ما هو ألودين 5200 المعالجة السطحية

ما هو ألودين 5200المعالجة السطحية العلاج ألودين 5200 هو الكروممنتج مجاني وصاغ خصيصا ل...

ما هو اكسيد الاسود؟

أوكسيد أسود ، اسوداد ، أكسدة ، أكسدة ، تخميل أسود ، مسدس غليظ. . . تشير جميع هذه المصط...

سياسة خاصة

لن نقوم بجمع وتخزين معلوماتك بأي شكل من الأشكال.

كيف ومتى تضيف نقوش ثني إلى أجزاء معدنية ورقة

ما هو الانحناء؟ إن الإغاثة المنحنى ليست أكثر من شقتين صغيرتين مقطوعة في قطعة من ال...
اتصل بنا
نائب المدير العام: Ivy
هاتف: 86-13312953695
هاتف: 86-755-82737317/82737469
الفاكس: 86-755-82737710
البريد الإلكتروني: المبيعات. china@xy-global.com
الرمز البريدي: 518129
Off Add: Room1702،17F، Building # 4، Tianan Cloud Park، No.2018 Xuegang Rd.، Longgang District، Shenzhen.
إضافة المصنع: Daling Industrial Area، Shaling، Fenggang Town، Dongguan City اتصل الآن

Sandblasting operation processing

Sandblasting operation processing

naky www.diecastingpartsupplier.com 2014-12-05 17:23:39
Sandblasting operation processing

1, the first open lights, after opening the compressed air valves, air spray nozzle 2 to 5 minutes , so that the pipe in the water spray out , so as not to wet sand and then shutting the valve will lose sand compressed air tube into the sand .

2 , and then into the working parts inside ( small pieces can be fitted with a basket ) , shut the door .

3, then start ventilation equipment , air valve open , blasting . When sandblasting nozzle should be tilted 30 ° ~ 40 °; should be evenly rotated or flipped back and forth slowly moving parts and parts or nozzles , so that parts of the surface subjected to a uniform jet , silver gray until the whole surface of the part so far. ( For the basket to hold small parts, parts jitter flip straight to reach blasting requirements . )

4 , where the parts have precision or finish requirements , you can not blast . If there are local requirements should not blast site on the same part , can only after blasting should be protected.

5 , each batch of parts after spraying , immediately shutting compressed air valve , and then unpack parts.

6, after the general parts sand , handed down procedure, as anti-rust treatment . But matt chrome parts , sandblasting plating treatment immediately after passing .

7 , only requires a cast iron hair spray blasting , sandblasting rust treatment is not performed immediately after passing the post processing plant
.